Capatect Schraubdübel Short 030
Plate anchor with European approval for fixing of Capatect facade systems
Field of Application
Screw anchor with pre-mounted, glass-fiber reinforced plastic screw and anchor plate for insulation thicknesses of 20-60 mm in surface-flush installation.
Approved fixing for Capatect facade insulation boards within Capatect facade systems in suitable substrates.
Material Properties
- Specifically for thin insulation boards
- Low anchoring depth in all use categories (A-E)
- Thermal bridge optimized
- Surface flush mounting
- Approved safe anchoring in all common wall materials
- Time saving processing
Colours
grayStorage
Cool, dry and protected from frost.Technical Data
| Approval | Product-No. | Length (mm) | Anchoring depth hnom (mm) | Packaging (units/box) |
Capatect Schraubdübel Short 030 Use category according to ETA, A = Concrete Weather shell ≥40 mm and <100 mm | 030/060 | 060 | ≥ 30 | 100 |
| 030/080 | 080 | ≥ 30✱ | 100 | |
| 030/100 | 100 | ≥ 30✱ | 100 | |
| ø-Plate (mm) | 60 | |||
| ø-Shaft (mm) | 8 | |||
✱In Use Category E, higher tensile capacities are required at greater anchoring depths (≥ 50 mm).
Supplementary Product
| Product name | Product-No. | Packaging (units/box) |
| Capatect Schraubdübel Short Tool Pro 030/01 for surface flush mounting | 030/01 | 1 |
| Capatect Schraubdübel Short Bit 030/02 for surface flush mounting | 030/02 | 1 |
| Capatect Dübelscheibe 153/VT 90 | 153/VT 90 | 100 |
| Capatect Dübelscheibe 153/140 | 153/140 | 100 |
Product No.
030Substrate Preparation
Ensure that the insulation boards are laid flat and that the edges are glued correctly.
The anchor length must be determined depending on the anchoring base, if necessary take any non-load-bearing layers and the system thickness into account.
Installation
The anchors should be installed only after sufficient solidification of the adhesive bed (approx. 1 day). The anchors length must be selected in such a way that the anchoring depth of at least 30 mm (aerated concrete at least 50 mm) in the solid wall material is given (without taking into account any old render layers or other non-load-bearing intermediate layers). Use a drilling machine (for vertically perforated bricks, sand-lime bricks and aerated concrete without percussion and hammering action) to drill the anchor holes Ø 8 mm, at right angles into the load-bearing structural member. Always drill about 10 mm deeper than the required anchoring depth. Before inserting the anchor, remove drill dust from the drill hole to ensure the required anchoring depth.Surface flush mounting:
Drill a hole through the insulation material into the load-bearing substrate. Drill hole depth for substrates of category A-E min. 40 mm at 30 mm anchoring depth. In substrate category E, drill hole depth min. 60 mm at 50 mm anchoring depth.
Combine anchors and anchor plates depending on the type of insulation material. Insert the screw acnhor into the drill hole and screw in the corresponding bit or tool so that it is flush with the surface. The anchor plate must lie flush with the surface after the setting process.
Anchor length determination:
La > hnom+ ttol+ hD
La = Anchor length
hnom = necessary anchoring depth
ttol = Tolerance compensation (thickness of adhesive layer) and, if necessary, non-bearing
Building component layers
hD = Insulation thickness
The tolerance compensation adds up from:
+ Thickness of non-load-bearing layers (thicknesses of old render, Mineral bonded wood wool boards, saving facing bricks, etc.). if present, often the thickness of old plaster is approx. 20 mm).
+ Thickness of the adhesive layer after pressing the insulation boards to the wall.
(as a rule, about 10 mm)
+ Additional compensation of facade unevenness
+ If necessary, the thickness of the base coat when fastening through the fabric.
Approval
ETA-17/0991Customer Service Centre
Tel.: +49 6154 71-71710Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com