Capatect Schlagdübel 061
Approved plastic plate anchor for fastening insulation boards
Field of Application
Approved impact anchor for fastening insulation boards in flush mounting in the Capatect façade systems. Depending on the installation variant and type of insulation board, additional anchor washers may have to be used.
Material Properties
- Telescopic plate for secure mounting flush with the surface
- Suitable for fastening fire bars
- Variable expansion zone from 25 to 55 mm for optimum setting even in critical substrates
- For all substrates (A-E)
- Absorption of large tensile forces
- Optimised for thermal bridges
Colours
blackTechnical Data
- Material: Polyethylene anchor sleeve and pre-assembled, galvanised special expansion nail with overmoulded glass-fibre reinforced drive-in head.
- Shaft diameter: Ø 8 mm
- Plate diameter: Ø 60 mm
- Chi value: 0.001 W/K (point-related heat transfer coefficient)
Supplementary Product
Capatect anchor disc 153/VT 90Capatect anchor disc 153/14
Product No.
061Anchortype | Product no. | Anchor length (mm) | Anchoring- | Packing |
Capatect Schlagdübel 061 Use category according to ETA, ✱ = Substrates A, B, C | 061/95 | 95 | ≥ 25✱/45✱✱ | 100 |
| 061/115 | 115 | ≥ 25✱/45✱✱ | 100 | |
| 061/135 | 135 | ≥ 25✱/45✱✱ | 100 | |
| 061/155 | 155 | ≥ 25✱/45✱✱ | 100 | |
| 061/175 | 175 | ≥ 25✱/45✱✱ | 100 | |
| 061/195 | 195 | ≥ 25✱/45✱✱ | 100 | |
| 061/215 | 215 | ≥ 25✱/45✱✱ | 100 | |
| 061/235 | 235 | ≥ 25✱/45✱✱ | 100 | |
| 061/255 | 255 | ≥ 25✱/45✱✱ | 100 | |
| 061/275 | 275 | ≥ 25✱/45✱✱ | 100 | |
| 061/295 | 295 | ≥ 25✱/45✱✱ | 100 |
Substrate Preparation
Lay the insulation boards flat and ensure that the edges are glued correctly. Determine the anchor length depending on the anchoring substrate, any non-load-bearing layers to be taken into account and the system thickness to be fixed.
Installation
The anchor type and anchoring depth must be matched to the substrate and the system variant to be implemented.
The effective expansion zone of the anchor is 55 mm. If the holding values are not sufficient, the anchor can also be set deeper with the minimum embedment depths of 25/45 mm.
With a drilling machine (for perforated bricks as well as aerated concrete without impact and hammering effect), the anchor holes, Ø 8 mm, are to be inserted at right angles into the load-bearing component. Always drill approx. 10 mm deeper than the selected anchor length. Clean the drill hole from dust and drill dust.
Insert the pre-assembled anchor into the insulation board and drive in the steel expansion pin using the GRP plug. The anchor plate must lie flat on the insulation surface, avoid sinking into the insulation.
Check that the anchors are firmly seated in the substrate. If an anchor is not properly fixed due to the substrate condition, it must be removed and a new anchor placed at an appropriate distance as a replacement.
Note:
Fastening the mineral wool boards:
Supplement the Capatect Schlagdübel 061 with the Capatect Dübelscheibe 153/VT90 (Ø 90 mm).
Fastening of mineral wool slats:
Complete the Capatect Schlagdübel 061 with the Capatect Dübelscheibe 153/14 (Ø 140 mm).
Anchor length determination:
La > hnom+ ttol+ hD
La = anchor length
hnom = necessary anchorage depth
ttol = tolerance compensation (thickness of adhesive layer) and, if applicable, non-load-bearing component layers
hD = insulation thickness
The tolerance compensation adds up to:
+ thickness of non-load-bearing layers (thicknesses of old render, HWL boards, saving facing bricks etc. if present, often the thickness of old plaster is approx. 20 mm)
+ Thickness of the adhesive mortar layer after pressing the insulation boards onto the wall
(usually approx. 10 mm)
+ Additional levelling of facade irregularities
+ If necessary, thickness of reinforcement layer when fastening through the mesh
Customer Service Centre
Tel.: +49 6154 71-71710Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com