Field of Application
Ready to use joint filler for vertical and horizontal joints in Meldorfer Flachverblender (flat facings).Material Properties
- ready for use, easy to apply
- dispersion based and cement-free compound of mineral fillers
- water vapour permeable
- weatherproof, water-repellent to DIN 18 550
- extremely low tension, highly ductile
- alkali-proof and UV-resistant
- pigmented
Packaging/Package Size
25 kg bucketColours
Cement-Grey
Storage
Cool, dry and frost free.Keep out of direct sunlight.
Empty containers and silos completely before longer interruptions (winter break).
Fire behaviour
Fire behaviour: German classification "schwerentflammbar” (hardly
combustible - of low flammability)
Coefficient of water absorption
w < 0.5 [ kg/(m2 · h0.5) ] nach DIN 52617Consistency
earth-moist
Product No.
081Consumption
Approx. 3-5 kg/m2 at approx. 12 mm joint width, depending on the depth and compression of material.The exact rate of consumption is best established by a trial application.
Application Conditions
Application Temperature:During application and drying the temperature should not fall below + 5 °C or rise over 30 °C for material, substrate, and surrounding air. Do not apply on sun heated substrates, during strong wind, fog, high relative humidity, imminent rain or impending night frost.
Drying/Drying Time
At 20 °C and 65% relative humidity:Surface-dry after 24 hours and thoroughly hardened after 2- 3 days.
Lower temperatures and a higher relative humidity will lengthen the drying times.
Tool Cleaning
Immediately after use with water.Application
Allow Meldorfer Ansatzmörtel 080 (adheslve and joint mortar) to cure and dry thoroughly. Curing time: for at least 2 - 3 days in warm weather conditions.The joint filler is ready to use, but should be stirred up before application and the consistency may be regulated by adding a small amount of tap (potable) water. First take a plot of material onto a trowel and then point the filler with a pointing trowel (size corresponding to the width of joints) into the joints. Smooth under slight pressure.
Superfluous material should be swept off with a hand brush before drying.
Being natural products, the mineral fillers used in the material may occasionally cause slight differences of shade in the dried material. lt is therefore recommended to use only material with identical batch numbers or, if using material from different batches, to blend the entire needed quantity in advance.
To avoid rain penetration during the drying process, protective tarpaulins should be used if required.
Keep out of reach of children.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. After contact with skin, wash immediately with soap and water.
Do not allow into drains, water or soil.
If swallowed, seek medical advice immediately, as the intestinal flora can be disturbed.
Germany: Only completely emptied packaging should be given tor recycling. Liquid remnants of material should be disposed of as waste ol water-mixable adhesives, hardened material should be disposed of as hardened adhesives or via household waste.
European Waste Code:EWC 08 04 10
Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com
To avoid rain penetration during the drying process, protective tarpaulins should be used if required.
Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)
Harmful to aquatic organisms, may cause long-term adverse effects.Keep out of reach of children.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. After contact with skin, wash immediately with soap and water.
Do not allow into drains, water or soil.
If swallowed, seek medical advice immediately, as the intestinal flora can be disturbed.
Disposal
Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.Germany: Only completely emptied packaging should be given tor recycling. Liquid remnants of material should be disposed of as waste ol water-mixable adhesives, hardened material should be disposed of as hardened adhesives or via household waste.
European Waste Code:EWC 08 04 10
Risk and Transportation Markings
See Material Safety Data Sheet
Giscode
D1Customer Service Centre
Tel.: +49 6154 71-71710Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com